Services catalog

C1 PVC EVA edging with curved edge up to 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 45 companies

C10 PVC PUR edging with curved edge over 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with edge with polyurethane PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 10 companies

C11 Edge cut edge

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with an edge of any type. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches. NOTE: this service is not picked by the material matrix — it is added by a separate check in the calculation (by a part attribute), so material and thickness conditions do not apply to it.

Unit: lin.m. Provided by 28 companies

C12 EVA curved edgebanding of glued-up panels

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is stitched parts (two blanks glued into one). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 17 companies

C13 PUR curved edgebanding of glued-up panels

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with edge with polyurethane PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is stitched parts (two blanks glued into one). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 4 companies

C14 Laser curved edgebanding of glued-up panels

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with laser (glue-free) edge. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is stitched parts (two blanks glued into one). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 1 companies

C15 Laser curved edgebanding, edge up to 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with laser (glue-free) edge. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 1 companies

C16 Laser curved edgebanding, edge over 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with laser (glue-free) edge. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 1 companies

C17 Laser curved edgebanding, part 25-50 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with laser (glue-free) edge. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the panel thickness is 25 mm or more. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 1 companies

C18 Laser curved edgebanding of worktops

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with laser (glue-free) edge. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 1 companies

C19 Curved edgebanding of acrylic panels, EVA

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is acrylic and high-gloss front panels (Acrylic, AGT, Plastic, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 4 companies

C2 PVC edging EVA 25-50mm curved

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm), the panel thickness is 25 mm or more. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 45 companies

C20 Curved edgebanding of acrylic panels, PUR

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with edge with polyurethane PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is acrylic and high-gloss front panels (Acrylic, AGT, Plastic, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 2 companies

C21 Curved PUR edgebanding of customer-supplied material

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with edge with polyurethane PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is customer-supplied material. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 3 companies

C22 Curved laser edgebanding of customer-supplied material

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with laser (glue-free) edge. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is customer-supplied material. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 1 companies

C23 PVC EVA curved edgebanding 25-50 mm, edge over 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm), the panel thickness is 25 mm or more. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 16 companies

C24 EVA curved edgebanding of worktops, edge up to 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 18 companies

C25 EVA curved edgebanding of worktops, edge over 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 19 companies

C3 PLASTIC EVA edging of worktops curved

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with plastic laminate with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is worktop plastic laminate (material type 16). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 38 companies

C4 Curvilinear edging EVA subcontracting material

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is customer-supplied material. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 39 companies

C4 PVC EVA edging with curved edge over 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with PVC edge with EVA adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 44 companies

C6 Edging complex parts

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with an edge of any type. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service. Unit of measure is the piece: the number of parts is counted, not the edge length. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches. NOTE: this service is not picked by the material matrix — it is added by a separate check in the calculation (by a part attribute), so material and thickness conditions do not apply to it.

Unit: pc Provided by 41 companies

C7 Curved plastic edging for PUR worktops

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with plastic laminate with PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is worktop plastic laminate (material type 16). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 5 companies

C8 Curved edge edging for PUR worktops

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with edge with polyurethane PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is a regular edge band, not worktop plastic. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 7 companies

C9 PVC PUR edging with curved edge up to 1 mm

Curved edge banding: covering radii, roundings, cut-outs and shaped edges with edge with polyurethane PUR adhesive. It runs on a curved-edge machine or by hand, so it is priced separately from straight edges. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 11 companies

A1 Cutting chipboard, chipboard, MDF, OSB up to 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is laminated chipboard, chipboard, MDF, OSB and related panel materials, panel thickness under 22 mm. Calculated by the total cut length (sheet-sale mode, calc_type=sheet/half_x/half_y): the length of all cuts on the sheet multiplied by the number of sheets. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 51 companies

A10 Cutting of other materials (sq.m.)

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is any other panel material not covered by a more specific group. Calculated by part perimeter (m²-sale mode, not by sheet): for each part made of this material, (X×2+Y×2)/1000 × quantity is computed and summed across all parts. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 24 companies

A11 Cutting client material

Cutting customer-supplied material. This service is charged IN ADDITION to the regular cutting service — for the same quantity (cut length or perimeter) as the main service — when the material is flagged as "customer material" (isDavalchMaterial). It is not attached to the part itself (used only for the order calculation, not the part production task). Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 42 companies

A12 Cutting laminated chipboard, chipboard, MDF, OSB over 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is laminated chipboard, chipboard, MDF, OSB and related panel materials, panel thickness 22 mm or more. Calculated by the total cut length (sheet-sale mode, calc_type=sheet/half_x/half_y): the length of all cuts on the sheet multiplied by the number of sheets. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 41 companies

A13 Cutting chipboard, chipboard, MDF, OSB from 21 mm (sq.m.)

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is laminated chipboard, chipboard, MDF, OSB and related panel materials, panel thickness 22 mm or more. Calculated by part perimeter (m²-sale mode, not by sheet): for each part made of this material, (X×2+Y×2)/1000 × quantity is computed and summed across all parts. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 21 companies

A14 Cutting per sheet chipboard, chipboard, MDF, OSB up to 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by the number of sheets (sheet-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness from 5 to 21 mm. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 13 companies

A15 Cutting per sheet of chipboard, chipboard, MDF, OSB over 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by the number of sheets (sheet-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness over 21 up to 28 mm. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 11 companies

A16 Cutting for a sheet of fiberboard, HDF.

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by the number of sheets (sheet-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness under 5 mm. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 13 companies

A17 Cutting per piece of worktops

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by the number of sheets (sheet-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness 28 mm or more, or a sheet of any thickness made of a worktop-group material. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 11 companies

A18 Cut per m2 of laminated chipboard, chipboard, MDF, OSB up to 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by sheet area (m²-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness from 5 to 21 mm. Unit of measure: square metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 10 companies

A19 Cut per m2 of laminated chipboard, chipboard, MDF, OSB over 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by sheet area (m²-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness over 21 up to 28 mm. Unit of measure: square metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 10 companies

A2 Fibreboard cutting, HDF

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is fibreboard and HDF. Calculated by the total cut length (sheet-sale mode, calc_type=sheet/half_x/half_y): the length of all cuts on the sheet multiplied by the number of sheets. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 47 companies

A20 Cut per m2 Fibreboard, HDF.

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by sheet area (m²-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness under 5 mm. Unit of measure: square metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 9 companies

A21 Cut per m2 of worktops

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. Priced by sheet area (m²-sale mode, panel-cutting price mode "by sheet"): the service is selected by the thickness of the whole sheet being cut: sheet thickness 28 mm or more, or a sheet of any thickness made of a worktop-group material. Unit of measure: square metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 11 companies

A22 Worktop packaging

An extra worktop-cutting surcharge: the number of WHOLE sheets needed for the order's parts is computed (part count divided by how many blanks fit on one sheet by its X×Y size, rounded to a whole number). Charged only for worktop-group materials and only if the firm setting production.serv_78_add is enabled — otherwise the service never applies. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 11 companies

A23 Cutting acrylic board (sheets)

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material has the catalogue type “Acrylic” — acrylic and related high-gloss panels (AGT, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). HPL and compact panels (type “Plastic”) do not belong to this group: they are charged as “Cutting of other materials” (A4 / A10). Calculated by the total cut length (sheet-sale mode, calc_type=sheet/half_x/half_y): the length of all cuts on the sheet multiplied by the number of sheets. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 33 companies

A24 Acrylic board cutting (m2)

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material has the catalogue type “Acrylic” — acrylic and related high-gloss panels (AGT, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). HPL and compact panels (type “Plastic”) do not belong to this group: they are charged as “Cutting of other materials” (A4 / A10). Calculated by part perimeter (m²-sale mode, not by sheet): for each part made of this material, (X×2+Y×2)/1000 × quantity is computed and summed across all parts. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 15 companies

A25 Cutting of an oversized part

A surcharge for an oversized part: charged once per part (by quantity) when the part's area (X1×Y1) exceeds the threshold from the firm settings (production.big_part_area_min) — e.g. for sliding-wardrobe panels, oversized fronts and similar large blanks that require special handling when sawing. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 24 companies

A3 Cutting worktops

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is worktops (postforming and related types). Calculated by the total cut length (sheet-sale mode, calc_type=sheet/half_x/half_y): the length of all cuts on the sheet multiplied by the number of sheets. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 45 companies

A4 Cutting remaining materials

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is any other panel material not covered by a more specific group. Calculated by the total cut length (sheet-sale mode, calc_type=sheet/half_x/half_y): the length of all cuts on the sheet multiplied by the number of sheets. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 44 companies

A5 Cutting materials when calculating sales m2

In the current calculation this service is never assigned automatically — there are no calls to it in the calculation code. Possible reasons: a legacy/reserved service, applied only manually by a manager, or the logic for it was never implemented. Check with the developers whether it is still relevant before using it.

Unit: lin.m. Provided by 16 companies

A6 Screed cutting

Cutting a glued block (a "stitch" — two blanks glued into one panel thicker than standard): the cut length comes from the stitch data, regardless of the block's combined thickness. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 46 companies

A7 Cutting of laminated chipboard, chipboard, MDF, OSB (sq.m.) up to 21 mm

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is laminated chipboard, chipboard, MDF, OSB and related panel materials, panel thickness under 22 mm. Calculated by part perimeter (m²-sale mode, not by sheet): for each part made of this material, (X×2+Y×2)/1000 × quantity is computed and summed across all parts. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 28 companies

A8 Fibreboard cutting, HDF (sq.m.)

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is fibreboard and HDF. Calculated by part perimeter (m²-sale mode, not by sheet): for each part made of this material, (X×2+Y×2)/1000 × quantity is computed and summed across all parts. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 22 companies

A9 Cutting countertops (sq. M)

Cutting (sawing) a sheet material into blanks of the required size on a panel saw. The service applies when the part material is worktops (postforming and related types). Calculated by part perimeter (m²-sale mode, not by sheet): for each part made of this material, (X×2+Y×2)/1000 × quantity is computed and summed across all parts. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 20 companies

H1 Hole

Drilling a hole in the part on a boring/drilling machine. Applies when the hole diameter is under 25 mm — the most common dowel/fitting diameter (5, 8, 10, 15 mm, etc.). Drilling is counted regardless of whether the hole is through or blind (except the special hinge-hole case — see the "Hinge drilling" service). Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 47 companies

H2 Drilling large diameters

Drilling a hole in the part on a boring/drilling machine. Applies for diameters from 25 to 59 mm inclusive — e.g. for hinge cups, sockets, larger-diameter fittings. Drilling is counted regardless of whether the hole is through or blind (except the special hinge-hole case — see the "Hinge drilling" service). Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 43 companies

H3 hole Ø 60 mm

Drilling a hole in the part on a boring/drilling machine. Applies for a diameter of EXACTLY 60 mm. This boundary was set deliberately: previously a 100 mm hole was priced as a 60 mm one; since 2026-09-03 anything above 60 mm goes to a separate "over 60 mm" service. Drilling is counted regardless of whether the hole is through or blind (except the special hinge-hole case — see the "Hinge drilling" service). Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 34 companies

H4 Hinge drilling

Hinge drilling: a special service for a blind hole with a diameter of EXACTLY 26 or 35 mm (drilling depth less than the part thickness) — standard hinge-cup diameters. NOT applied to worktop-group materials (for them such a hole is priced by the general diameter rules — the "hole up to 59 mm" service). Takes priority over the general diameter services: if the condition is met, this service applies instead of "hole up to 59 mm". Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 48 companies

H5 Hole over 60 mm

Drilling a hole in the part on a boring/drilling machine. Applies when the diameter is GREATER than 60 mm (exactly 60 mm is a separate service, see above). Added on 2026-09-03 so large holes are not priced as 60 mm ones. Drilling is counted regardless of whether the hole is through or blind (except the special hinge-hole case — see the "Hinge drilling" service). Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 16 companies

G1 Slot open up to 9 mm

An open groove up to 9 mm wide (before the wide-groove pass multiplier): milled when there are no end offsets (the groove runs across the whole side of the part) and the groove type is "open". Length is the part's side length minus the offsets; if the groove is wider than the cutter, it is multiplied by the number of passes. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 47 companies

G2 Closed groove up to 9 mm

A closed groove up to 9 mm wide: same logic as the open groove (see "Open groove"), but applies when the groove has end offsets (does not reach the edge on one or both sides) or its type is "closed". Also multiplied by the number of passes for a wide groove. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 49 companies

G3 Quarter to 10mm

A rabbet (a groove open at the end, up to 10 mm wide): milled on the front or back face of the part when the groove depth on one side is zero (the groove reaches the part's edge). Calculated by groove length. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 46 companies

G4 End slot

An end-face groove: applied instead of the regular open/closed groove when at least one of the special firm settings is enabled (converting a wide groove to a pocket, cutting a wide groove differently, milling instead of sawing, bb→cut groove conversion) AND the groove is on the end-face side of the part (the SIDE constant). Length and the pass-count multiplier are computed the same way as for a regular groove. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 36 companies

J1 Milling cut length (400-600 mm)

A milling cut (a through cut-out in the part, operation depth at least the part thickness): calculated by the length of the cut-out contour. The service is chosen by contour length — over 400 up to 600 mm. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 43 companies

J10 milling cut handle

A milling operation recognised by the part's XNC shape template: a shaped handle recess (an integrated grip milled into a front panel). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 29 companies

J11 milling cut U-shaped cut

A milling operation recognised by the part's XNC shape template: a U-shaped cut-out (e.g. for a sink, hob, socket). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 22 companies

J12 milling cut circle

A milling operation recognised by the part's XNC shape template: a round cut-out (e.g. for a hob, a decorative hole). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 9 companies

J13 milling cut arc

A milling operation recognised by the part's XNC shape template: an arc (a curved section of the part's contour). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 8 companies

J14 milling cut worktop rounding

A milling operation recognised by the part's XNC shape template: a worktop corner rounding (the characteristic radius on a worktop corner). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 26 companies

J15 milling cut worktop screed

A milling operation recognised by the part's XNC shape template: a worktop joining fitting recess (a groove/cut-out for the worktop joint connector). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 23 companies

J16 milling cut countertop lock

A milling operation recognised by the part's XNC shape template: a worktop lock recess (a cut-out for the eccentric connector lock at the worktop joint). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 32 companies

J17 Finishing 90 degree angles with a smaller cutter

Reworking 90° internal corners with a smaller cutter: a milling machine leaves a radius in internal corners (equal to the cutter diameter), so the sharp corner is finished by hand or with a smaller cutter as a separate pass. Charged by the number of such corners on the part (or by the operation flag, if a 90° corner is recognised), multiplied by the part quantity. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 24 companies

J2 Milling cut length (up to 400 mm)

A milling cut (a through cut-out in the part): applies to a short contour — up to 400 mm inclusive. Unlike the other length ranges, it is priced PER PIECE (the operation itself counts as 1 unit, not by actual length) — short cut-outs (small non-standard holes, lock recesses, etc.) are not cheaper this way, but are priced as a minimum operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 45 companies

J3 Milling cut length (600-800 mm)

A milling cut (a through cut-out in the part, operation depth at least the part thickness): calculated by the length of the cut-out contour. The service is chosen by contour length — over 600 up to 800 mm. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 45 companies

J4 Milling cut length (801-1000 mm)

A milling cut (a through cut-out in the part, operation depth at least the part thickness): calculated by the length of the cut-out contour. The service is chosen by contour length — over 800 up to 1000 mm. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 45 companies

J5 Milling cut length (over 1000 mm)

A milling cut (a through cut-out in the part): applies to the longest contour — over 1000 mm. Calculated by the actual contour length. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 46 companies

J6 Notch (milling)

A pocket (a blind milling operation, depth less than the part thickness — no through hole, material remains): calculated by the area of removed material (for a circular shape — by the circle area formula). A back-side recess for a sink overlay, if detected, is charged separately at the same rate. Unit of measure: square metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: m² Provided by 42 companies

J7 milling cut corner radius

A milling operation recognised by the part's XNC shape template: a corner radius (a rounded outer corner of the part). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 10 companies

J8 milling cut corner cut

A milling operation recognised by the part's XNC shape template: a corner cut-off (a straight chamfer instead of the part's sharp corner). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 24 companies

J9 milling cut corner overcut

A milling operation recognised by the part's XNC shape template: a corner notch (a complex-shaped internal corner cut-out). The service is chosen automatically by the recognised template code (the TemplatesApi/xnc_template reference), not by geometric thresholds — so the exact set of templates leading to this service may grow as new templates are added to the reference. Charged by the number of parts with such an operation. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 7 companies

M1 packaging of parts in boxes for sending a delivery service.

Packing parts into boxes for shipment by a delivery service — designed for transport by courier/postal services, not pallet logistics. An order packing method. Unlike other services, packing is NOT chosen automatically by material or operations — it is one of the options the manager/customer selects manually when placing the order (or does not select at all — there is a "no packing" option). The list of available options is limited by the firm setting production.service_pack_available (a comma-separated list of allowed method numbers); unavailable options are not shown to the customer. Quantity is calculated by the TOTAL AREA of the packed parts. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 8 companies

M2 packaging of parts in cardboard inside pallets

Packing parts in cardboard on a pallet — parts are wrapped in cardboard and placed on a pallet to protect them during transport by large-scale freight. An order packing method. Unlike other services, packing is NOT chosen automatically by material or operations — it is one of the options the manager/customer selects manually when placing the order (or does not select at all — there is a "no packing" option). The list of available options is limited by the firm setting production.service_pack_available (a comma-separated list of allowed method numbers); unavailable options are not shown to the customer. Quantity is calculated by the TOTAL AREA of the packed parts. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 32 companies

M3 packaging on a pallet with a tape

Pallet packing with strapping — parts are placed on a pallet and secured with strapping tape without film, for lighter and cheaper securing. An order packing method. Unlike other services, packing is NOT chosen automatically by material or operations — it is one of the options the manager/customer selects manually when placing the order (or does not select at all — there is a "no packing" option). The list of available options is limited by the firm setting production.service_pack_available (a comma-separated list of allowed method numbers); unavailable options are not shown to the customer. Quantity is calculated by the TOTAL VOLUME of the packed parts, divided by the volume of one pallet slot (0.8×1.2 m × pallet height from the firm settings, usually 0.3 m) and rounded up to a whole number of pallets. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 29 companies

M4 packaging on a pallet with a stretch

Pallet packing with stretch film — parts are placed on a pallet and fully wrapped in stretch film for moisture protection and more secure fixation than strapping. An order packing method. Unlike other services, packing is NOT chosen automatically by material or operations — it is one of the options the manager/customer selects manually when placing the order (or does not select at all — there is a "no packing" option). The list of available options is limited by the firm setting production.service_pack_available (a comma-separated list of allowed method numbers); unavailable options are not shown to the customer. Quantity is calculated by the TOTAL VOLUME of the packed parts, divided by the volume of one pallet slot (0.8×1.2 m × pallet height from the firm settings, usually 0.3 m) and rounded up to a whole number of pallets. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 38 companies

K1 Chipboard screed up to 1 sq.

Chipboard stitching (edge-gluing two panels into one to get a width/length bigger than a standard sheet): applies when the part has a stitching (hem) operation or the "double main part" flag, the part area is under 1 m², and the firm setting for per-m² stitching pricing is disabled (production.double_m2_price_service ≠ 1). Priced PER PIECE (by part quantity), not by area. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 39 companies

K2 Chipboard screed from 1 to 2 sq.

Chipboard stitching (edge-gluing two panels into one to get a width/length bigger than a standard sheet): applies when the part has a stitching (hem) operation or the "double main part" flag, the part area is from 1 to 2 m², and the firm setting for per-m² stitching pricing is disabled (production.double_m2_price_service ≠ 1). Priced PER PIECE (by part quantity), not by area. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 39 companies

K3 Chipboard screed from 2 sq.

Chipboard stitching (edge-gluing two panels into one to get a width/length bigger than a standard sheet): applies when the part has a stitching (hem) operation or the "double main part" flag, the part area is 2 m² or more, and the firm setting for per-m² stitching pricing is disabled (production.double_m2_price_service ≠ 1). Priced PER PIECE (by part quantity), not by area. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 38 companies

K4 Chipboard screed per sq.m.

Chipboard stitching, priced BY AREA: applies instead of the three per-piece services (see "Chipboard stitching up to 1/1-2/from 2 m²") when the firm setting production.double_m2_price_service = 1 — then stitching is priced by the part's area rather than in quantity brackets. Also used for stitching sheets of combined material (calculated by the glued block's area). Unit of measure: square metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: m² Provided by 21 companies

B1 PVC EVA straight edge edging up to 1 mm

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 44 companies

B10 Straight edge banding of acrylic and high-gloss front panels with PUR edge

Straight edge banding: covering the straight edges of a part with PVC edge with PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is acrylic and high-gloss front panels (Acrylic, AGT, Plastic, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 39 companies

B11 Straight edge edging of EVA acrylic boards

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. Intended for a part material of acrylic and high-gloss front panels (Acrylic, AGT, Plastic, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 31 companies

B12 Straight edging of PUR acrylic boards

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is acrylic and high-gloss front panels (Acrylic, AGT, Plastic, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 39 companies

B13 Edging of a large part

Straight edge banding: covering the straight edges of a part with an edge of any type on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches. NOTE: this service is not picked by the material matrix — it is added by a separate check in the calculation (by a part attribute), so material and thickness conditions do not apply to it.

Unit: pc Provided by 24 companies

B2 PVC edging EVA 25-50mm straight

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the panel thickness is above 22 mm. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 40 companies

B3 Edging PVC EVA worktops

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is a regular edge band, not worktop plastic. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 40 companies

B4 PLASTIC EVA edging of worktops

Straight edge banding: covering the straight edges of a part with plastic laminate with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is worktop plastic laminate (material type 16). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 36 companies

B5 Straight edge EVA stitching

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is stitched parts (two blanks glued into one). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 43 companies

B6 PVC EVA straight edge edging over 1 mm

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 41 companies

B7 Straight edge edging of EVA subcontracting material

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is customer-supplied material. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 39 companies

B8 Straight edge edging for 8-15 mm thick slabs

Straight edge banding: covering the straight edges of a part with PVC edge with EVA adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the panel thickness is from 8 to 15 mm inclusive. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 39 companies

B9 Plastic edging for PUR worktops

Straight edge banding: covering the straight edges of a part with plastic laminate with PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is worktop plastic laminate (material type 16). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 30 companies

D1 Edging PVC PUR glue with straight edge up to 1mm

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the edge thickness does not exceed the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm), the panel thickness is below 25 mm. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 44 companies

D2 Edging PVC PUR glue 25-50mm straight

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the panel thickness is 25 mm or more. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 44 companies

D3 Edging PVC PUR glue with straight edge over 1 mm

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the edge thickness is above the "thick edge" threshold from the company settings (production.edge_thikness_big_for_price, usually 1 mm), the panel thickness is below 25 mm. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 42 companies

D3 Edging of PUR PVC worktops with adhesive

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types), the banding material is a regular edge band, not worktop plastic. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 40 companies

D4 Straight edge PUR stitching

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is stitched parts (two blanks glued into one). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 42 companies

D5 Straight edge edging of PUR subcontracting material

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is customer-supplied material. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 38 companies

D6 Straight PUR edgebanding of 8-15 mm panels

Straight edge banding: covering the straight edges of a part with edge with polyurethane PUR adhesive on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is laminated chipboard and related panel materials, the panel thickness is from 8 to 15 mm inclusive. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 18 companies

E1 Straight laser edging

Straight edge banding: covering the straight edges of a part with laser (glue-free) edge on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the panel thickness is below 25 mm. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 5 companies

E2 Straight edge edging 25-50mm laser edging

Straight edge banding: covering the straight edges of a part with laser (glue-free) edge on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is any panel material not covered by a more specific service, the panel thickness is 25 mm or more. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 5 companies

E3 Straight laser stitching edging

Straight edge banding: covering the straight edges of a part with laser (glue-free) edge on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is stitched parts (two blanks glued into one). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 5 companies

E4 Laser edging straight line

Straight edge banding: covering the straight edges of a part with laser (glue-free) edge on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is customer-supplied material. Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 5 companies

E5 Straight laser edgebanding of worktops

Straight edge banding: covering the straight edges of a part with laser (glue-free) edge on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is worktops (postforming and related types). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 1 companies

E6 Straight laser edgebanding of acrylic panels

Straight edge banding: covering the straight edges of a part with laser (glue-free) edge on an automatic edge banding machine. The calculation applies this service automatically when all of the following hold: the part material is acrylic and high-gloss front panels (Acrylic, AGT, Plastic, LuxeForm, Venni, Skin, Alvik, EKOshpon GIZIR). Unit of measure is the running metre: the total length of banded edges multiplied by the number of parts in the line. The result appears in the order calculation as a separate service line, in the customer specification and in the production task for the edge banding station; the price comes from the company price list for this service. Check order matters: stitched parts, customer-supplied material and worktops are handled earlier and override this service even when the material formally matches.

Unit: lin.m. Provided by 1 companies

L1 Cutback

Trimming a part's side to a required size (e.g. on-site fitting, adjustment to actual dimensions). Calculated separately for each trimmed side of the part (top/bottom/left/right): the length of that side (X1 or Y1, depending on which side is trimmed) in metres, multiplied by the part quantity. If several sides of the same part are trimmed, they are summed. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 47 companies

L2 Cut of the butt end at an angle of + 45 / -45 degrees more than 1 m.

A ±45° angled end-cut on the part (e.g. an outer/inner corner with no edge banding at the cut face): applied on a side of the part flagged as angle-cut (no edge on that side, db_id=-1) or as a "cut" with a set angle. Applies when this side of the part is LONGER THAN OR EQUAL TO the threshold from the firm settings (production.srez_calculate_by_m_start_length, default 1 m) — priced by the cut length in metres. Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 46 companies

L3 End cut at an angle of + 45 / -45 degrees less than 1 m.

A ±45° angled end-cut on the part (e.g. an outer/inner corner with no edge banding at the cut face): applied on a side of the part flagged as angle-cut (no edge on that side, db_id=-1) or as a "cut" with a set angle. Applies when this side of the part is SHORTER than the threshold from the firm settings (production.srez_calculate_by_m_start_length, default 1 m) — in this case the operation is priced PER PIECE (by part quantity), not by length. Unit of measure: piece. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: pc Provided by 45 companies

L4 Edge cutting

Edge-band trimming: an additional operation applied when the width of the edge banding material is GREATER than the part thickness plus double the process gap from the firm settings (production.min_delta_edge_material) plus 1 mm — i.e. the band is wider than the panel and the excess must be trimmed flush after gluing. Charged together with the main edge-banding service, for the same quantity (length of the banded side). Unit of measure: running metre. The result appears in the order calculation as a separate service line, in the customer specification and in the production task of the corresponding station; the price comes from the company price list for this service.

Unit: lin.m. Provided by 44 companies